Gordon

                               Bifilar MAG Coil 08-08-16

Highlights:

* Fabrication Cost $75.00.  * A (Magnetic Wave - Scalar Wave & PEMF) delivery device.  * This device is being replaced with a much larger and more powerful coil.  It will be available before the end of the month. 

Description:

The MAG Coil is a bifilar wound coil used to generate complex magnetic waves, scalar or longitudinal waves, and extremely strong magnetic pulses.  It was developed as a replacement for a Vortex Coil while having the capability of also being used as a PEMF delivery device.   It is intended to be used with a dual channel function generator such as the Spooky2 or a PEMF generator like the ‘PEMF Bob Beck’ project listed on this website.  It is capable of being driven directly by the Spooky2 outputs or an amplifier can be added to generate much more powerful magnetic wave fronts.

As a Rife delivery device the MAG coil is a non-contact magnetic field generator.  A single coil lays down a circular magnetic wave front, radiating outward from the coil and is measurable with a Trifield 100XE meter.  A simple Spooky2 unamplified 3000 Hz  signwave delivers 100 milligauze at 8 inches. The Trifield maximum scale reading is 100 milligauze. When using an amplifier with the Spooky2, pegging the meter at 2 feet is easily accomplished.  This range can be further extended when two synchronized coils are placed out of phase so the north and south fields pull at one another.

When operated in the ‘Inverse Sync’ mode on a two channel generator, like the Spooky2, the MAG Coil can produce very intense opposing standing waves.  Thus the MAG is a powerful scalar wave delivery device.  With a ‘Polarity Reverser’ and the Spooky2 Boost, even stronger opposing standing waves can be generated.  NOTE: The Spooky2 Boost must be used with a ‘Polarity Reverser’ to support this scalar wave voltage doubling feature.

the MAG Coil is also an intense magnetic pulse generator when used with the PEMF Bob Beck style device.   The New MAG Coil consists of two #18 gage  wire windings.  They are wound side by side on 2.25” spindle with a center core diameter of 1”.  The spindle is 1.25 inches wide.  As a PEMF delivery device the 18 gauge winding is used to handle a 60 Amp 100 volt pulse train, capable of generating multi gauze strength magnetic pulses.

Coil Considerations:

The “Bifilar MAGnetic Coil’ RUNS / WORKS with all the Spooky protocols that previously used the TENS Pads, Hand Grips, PEMF Coil, and Remotes.  Electric fields are replaced with magnetic fields and in many cases can be more effective than electric fields.  Scaler waves are handle in the same way the Spooky Remotes handles scalar wave.  Finger nail clippings can be placed in the 1” diameter coil core center.  All infrared, ultraviolet, and LED protocols can be run using magnetic waves verse the light waves.  Magnetic waves can run along side or replace all other wave types.

The MAG Coil is polyurethaned on each layer of the windings to help eliminate wire vibration.  There is a 330 ohm resistor placed in each leg of the coil  to allow direct connection to the function generator outputs.   The resistors are in the RCA phono to AC plug adapters cables.  When using the coil as a PEMF delivery device it will get uncomfortably hot after 5 minutes of use when the pulse strength is set to maximum.  Use a sock or small hand towel to cover the coil so it can be handled.  20 to 30 minutes are typical maximum run times in PEMF mode.  Do not run the coil for more than 30 minutes to avoid a melt down.  The coil was tested for 1 hour at maximum pulse mode.  It got hot but did not melt the plastic spindle.  Depending how the coil is connected, series or parallel, will change the ohmic and inductance values.  Without the iron core the resistance and inductance values of each winding is .68 ohms and .72 millihenrys  respectively.  Coil Fabrication cost is $75.00.  Use the ‘Contact Button’ for more information.

Last updated 08-24-17 by author gsk